Do you need a vapor barrier with Redgard?
Paint on membranes can also be used, such as RedGuard or AquaDefense. This a is a recent job I completed illustrating Kerdi over Hardibacker. I called USG,the maker of Durock cement board Next Gen, and they advised using no vapor barrier so that the wall cavity can breath and allow any moisture to evaporate.
Simply so, What is dent shield?
Ding Shield — Dent Protection and More
Being protected against everyday occurrences—such as run-away shopping carts, flying rocks or vertical curbs waiting to scuff your wheels—is one of the best ways to invest in the appearance of your vehicle and keep it looking as good as new and help retain its value.
Can you use Densglass in a shower? The densglass is used in place of normal gypsum sheathing and is installed against the exterior framing prior to the tub / shower installation. This densglass sheathing will withstand the elements, and will not promote any deterioration or mold, mildew buildup.
22 Related Questions Answers Found
Can you finish DensGlass?
Panels are applied directly to structural framing. Surface and joints may be finished and painted, or surfaced with an exterior finish system. DensGlass Sheathing is resistant to normal weather conditions, but it is not intended for immersion in water.
What is the best cement board for shower walls?
Tile Backer Board Breakdown
- Foam boards are lightweight, easy to cut, and a completely waterproof. Pictured: Wedi Board tile backer board.
- Schluter approves Kerdi over drywall.
- Hardibacker is the best known fiber cement board.
- Cement board has improved over the years and is easier to work with.
How do you cut a DensShield tile backer?
Cut panel to required size and make cutouts. Fit ends and edges closely. Do not leave gaps between panels. DensShield Tile Backer may be cut by using a utility knife to score, then snap, working from the grey face side.
What is dent shield?
Ding Shield — Dent Protection and More
Being protected against everyday occurrences—such as run-away shopping carts, flying rocks or vertical curbs waiting to scuff your wheels—is one of the best ways to invest in the appearance of your vehicle and keep it looking as good as new and help retain its value.
What is DensShield made of?
DensShield Tile Backer is composed of a water-resistant treated core that is covered front and back with fiberglass mats. The mats are permanently integrated with the core during manufacturing, preventing delamination problems that can occur with paper- faced greenboard.
How do you speed up DensGlass?
Fasteners should be driven flush with the panel surface (not countersunk) and into the framing system. Locate fasteners at least 3/8” (9 mm) from the ends and edges of the sheathing. Nails or screws, as listed in the fastener chart, may be used to attach DensGlass Sheathing to framing.
Does Home Depot carry DensShield?
DensShield Gypsum Backer Board 1/2 in. x 2.7 ft. x 5 ft. Tile Backer-008590 – The Home Depot.
What is GoBoard?
What is GoBoard?
GoBoard is the innovative tile backer board by Johns Manville that is ultra-lightweight, waterproof, durable, easy to cut, and install. GoBoard is also up to 80% lighter than traditional boards. Engineered and tested for strength and durability yet can be cut right where its installed using a utility knife.
What is Densboard?
DensShield® Tile Backer
The first backer board with a built-in moisture barrier. Engineered to prevent damage to the sub-floor or wall cavity if moisture seeps through grouted tile, DensShield® Tile Backer is the first backer board with a built-in moisture barrier.
How do you finish backer board?
Push the mortar through the mesh tape and into the 1/8-inch space between the backer board and the drywall. Run the drywall knife over the mortar to create a smooth finish and remove any excess material.
Is DensGlass waterproof?
DensGlass Sheathing is the ideal substrate for a wide variety of air and water-resistive barriers including building wraps, fluid applied coatings, self-adhering membranes and spray foam applications. See page 10 for details. DensGlass Sheathing is lightweight and easy to handle.
Does cement board wick water?
If you use cement backer board, you have to install a separate moisture barrier between the board and any wood it’s attached to. Since the concrete can absorb and wick moisture, the barrier prevents wood rot if the backer board gets saturated with water.
What kind of screws do you use with DensShield?
No special or unique fasteners are required to fasten DensShield Tile Backer panels in place. For wood studs: galvanized roofing nails, rust-resistant drywall screws or bugle head deck screws. Fasteners should be long enough to penetrate at least 3⁄49 (19 mm) into the wood framing members.
What is the best material to use for shower walls?
If you use cement backer board, you have to install a separate moisture barrier between the board and any wood it’s attached to. Since the concrete can absorb and wick moisture, the barrier prevents wood rot if the backer board gets saturated with water.
What is the best material to use for shower walls?
Push the mortar through the mesh tape and into the 1/8-inch space between the backer board and the drywall. Run the drywall knife over the mortar to create a smooth finish and remove any excess material.
Can you use 1/4 Hardibacker walls?
When butting HARDIBACKER ® sheets to 1/2″ drywall, tack 1/4” thick furring strips to each stud. In wet areas, install a moisture barrier (such as 15 lb. roofing felt) between studs and HARDIBACKER ® sheets. Install sheets 1/4” above floor, tub or shower pan.
Do I need to waterproof DensShield?
Showers with curbs— apply waterproof membrane up the walls a minimum of 29 (51 mm) and a maximum of 49 (102 mm) above curb. Showers without curbs — apply waterproof membrane up the walls a minimum of 69 (152 mm) and a maximum of 89 (203 mm). DensShield Tile Backer panels should not be used in shower curbs.
Does DensShield need Redgard?
They also confirmed that it is okay to apply a water-proofing membrane such as Redgard to the face of the Densshield (nothing is to go on the back).
Does DensShield need Redgard?
They also confirmed that it is okay to apply a water-proofing membrane such as Redgard to the face of the Densshield (nothing is to go on the back).
Which is better Hardibacker or durock?
HardieBacker® cement board is a unique, cement based water resistant tile backerboard that can be used on walls, floors and worktops. The products meet the European standard for fibre cement – EN 12467 and its reaction to fire, in accordance with EN 13501-1, is A1,S1-d0.
Can DensShield be painted?
The nontiled areas can be primed and painted with the same finish used on the other walls in the room as long as the primer and paint are suitable for high-moisture areas.
What is the best backer for tile?
Cement board is a good, reliable backer board that works well on both floors and walls. Keep in mind that most tile setters err on the side of caution and brush a waterproofing membrane on top of cement board when it is in wet areas like showers or tub surrounds.
What is the best backer for tile?
What is the best material to use for shower walls?
What is gypsum backer board?
Water-resistant gypsum backing board (see ASTM C 1396, Standard Specification for Gypsum Board) is designed to be used as a base for the appli- cation of ceramic or plastic wall tile or plastic fin- ished wall panels in wet areas.
Is tile backer board fireproof?
Yes, HardieBacker® 1/4″ Cement Board is deemed noncombustible when tested to ASTM E 136 and can be used in conjunction with other noncombustible materials around a fireplace. This does not mean that clearances to combustible building materials can be reduced by using HardieBacker 1/4″.
What is DensGlass used for?
Widely recognized by the GOLD color, DensGlass® fiberglass mat gypsum sheathing has an exemplary track record that spans more than 30 years. It is a preferred substrate under brick, stone, stucco, siding and EIFS due to its ability to protect a structure against incidental moisture during and after construction.
What is gypsum backer board?
Water-resistant gypsum backing board (see ASTM C 1396, Standard Specification for Gypsum Board) is designed to be used as a base for the appli- cation of ceramic or plastic wall tile or plastic fin- ished wall panels in wet areas.
Is tile backer board fire resistant?
Yes, HardieBacker® 1/4″ Cement Board is deemed noncombustible when tested to ASTM E 136 and can be used in conjunction with other noncombustible materials around a fireplace. This does not mean that clearances to combustible building materials can be reduced by using HardieBacker 1/4″.
Is Hardie backer waterproof?
cement backer board is not waterproof,but water cant hurt it,even when soaked in water for months or even years
Does it matter which side of durock faces out?
HardieBacker® cement board is a unique, cement based water resistant tile backerboard that can be used on walls, floors and worktops. The products meet the European standard for fibre cement – EN 12467 and its reaction to fire, in accordance with EN 13501-1, is A1,S1-d0.
ncG1vNJzZmiZlKG6orONp5ytZ5Skerq71Galnp2UYq5uwsCppqtlkpa%2Fs7XEq2SwoaSderOxw6CYq5xf